学派网关于网络接口配置Bonding的实例教程-linux教程

如果您有服务器咨询问题、购买问题、可以联系我们客服 7271895 690624
商祺云-阿里代理、景安代理、西部代理

就是讲到快网卡绑定到同一IP地址对外服务，可以实现高可用或者负载均衡。当然，直接给两块网卡设置同一IP地址是不可能的。通过bonding，虚拟一块网卡对外提供连接，物理网卡被修改为同一MAC地址。

一 Bonding 的工作模式

Mode 0 (balance-rr)

轮转（Round-robin）策略：从头到尾顺序的在每一个slave接口上面发送数据包。本模式提供负载均衡和容错的能力。

Mode 1 (active-backuop)

活动-备份（主备）策略：在绑定中，只有一个slave被激活，当且仅活动的slave接口失败是才会激活其他的slave。为了避免交换机发生混乱此时绑定的MAC地址只有一个外部端口上可见。

Mode 3 (broadcast)

广播策略：在所有的slave接口上发送所有的报文。本模式提供容错能力。

二 Bonding配置

1 创建bonding设备的配置文件

[root@CentOS68 ~]# vim /etc/sysconfig/network-scripts/ifcfg-bond0

DEVICE=bond0

BOOTPROTO=none

BONDING_OPTS=”miimon=100 mode=0″

IPADDR=200.200.200.200

PREFIX=24

GATEWAY=200.200.200.1

miimon是设置检测链路的时间，单位为毫秒。如果miimon=100，那么系统每100毫秒检测一侧链路的连接状态，如果有一条线路不通就转入另一条线路。

mode用来指定模式

2 创建slave的配置文件

既就是要加入的网卡的配置文件，这里使用eth1、eth2两块网卡，下来修改两块网卡的配置

[root@CentOS68 ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth1

DEVICE=eth1

TYPE=Ethernet

BOOTPROTO=none

MASTER=bond0

SLAVE=yes

USERCTL=0

MASTER指定测网卡属于哪个bond。SLAVE指定从属关系。USERCTL指定用户是否有控制权限。

eth2和eth1配置类似

[root@CentOS68 ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth2

DEVICE=eth2

TYPE=Ethernet

BOOTPROTO=none

MASTER=bond0

SLAVE=yes

USERCTL=0

3 重启网络服务

[root@CentOS68 ~]# service NetworkManager stop #centos6上不稳定，建议关闭
[root@CentOS68 ~]# service network restart

Shutting down interface bond0: [ OK ]

Shutting down interface eth0: [ OK ]

Shutting down loopback interface: [ OK ]

Bringing up loopback interface: [ OK ]

Bringing up interface bond0: Determining if ip address 200.200.200.200 is already in use for device bond0…

[ OK ]

Bringing up interface eth0: Determining if ip address 192.168.29.68 is already in use for device eth0…

[ OK ]

可以看到已经启动成功，再来看下IP地址和MAC

[root@CentOS68 ~]# ip a

[……]

7: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP qlen 1000

link/ether 00:0c:29:74:74:45 brd ff:ff:ff:ff:ff:ff

8: eth2: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 state UP qlen 1000

link/ether 00:0c:29:74:74:45 brd ff:ff:ff:ff:ff:ff

9: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP

link/ether 00:0c:29:74:74:45 brd ff:ff:ff:ff:ff:ff

inet 200.200.200.200/24 brd 200.200.200.255 scope global bond0

inet6 fe80::20c:29ff:fe74:7445/64 scope link tentative dadfailed

valid_lft forever preferred_lft forever

可以看到IP地址已经生效，并且MAC地址都相同。

4 查看bond0的状态

[root@CentOS68 ~]# cat /proc/net/bonding/bond0

Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: load balancing (round-robin)

MII Status: up

MII Polling Interval (ms): 100

Up Delay (ms): 0

Down Delay (ms): 0

Slave Interface: eth1

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:74:74:45

Slave queue ID: 0

Slave Interface: eth2

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:74:74:4f

Slave queue ID: 0

好了，一切都很顺利

5 删除bond

[root@CentOS68 ~]# ifconfig bond0 down

[root@CentOS68 ~]# rmmod bonding

看下是否删除成功，

[root@CentOS68 ~]# ifconfig bond0

bond0: error fetching interface information: Device not found

已经找不到bond0，说明删除成功。

详细帮助：/etc/share/doc/kernel-doc-version/Documentation/networking/bonding.txt

三 nmcli实现bonding

1 添加bonding接口

[root@centos7 ~]# nmcli connection add type bond con-name mybond0 ifname bond0 mode active-backup

Connection ‘mybond0’ (cc101e79-3dcb-49ee-8164-89c9e877c315) successfully added.

2添加从属接口

[root@centos7 ~]# nmcli connection add type bond-slave ifname ens34 master mybond0

Connection ‘bond-slave-ens34’ (9c8ff11a-72ef-4d63-a950-2ab777d2a1ea) successfully added.

[root@centos7 ~]# nmcli connection add type bond-slave ifname ens38 master mybond0

Connection ‘bond-slave-ens38’ (c40b3e6f-32f4-4d1a-a323-aed2519cf865) successfully added.

注意：如没有指定从属接口连接名，则该名称是接口名称加类型构成

3 启动从属接口

[root@centos7 ~]# nmcli connection up bond-slave-ens34

Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/40)

[root@centos7 ~]# nmcli connection up bond-slave-ens38

Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/41)

4 启动bonding 绑定

[root@centos7 ~]# nmcli connection up mybond0

Connection successfully activated (master waiting for slaves) (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/48)

5 查看绑定

[root@centos7 ~]# nmcli connection show

NAME UUID TYPE DEVICE

bond-slave-ens34 9c8ff11a-72ef-4d63-a950-2ab777d2a1ea 802-3-ethernet ens34

bond-slave-ens38 c40b3e6f-32f4-4d1a-a323-aed2519cf865 802-3-ethernet ens38

mybond0 cc101e79-3dcb-49ee-8164-89c9e877c315 bond bond0

6 添加IP地址

[root@centos7 ~]# nmcli connection modify mybond0 ipv4.method manual ipv4.addresses 200.1.1.1/24

7 删除bond绑定

（1）关闭bond

[root@centos7 ~]# nmcli connection down mybond0

Connection ‘mybond0’ successfully deactivated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/18)

[root@centos7 ~]#

（2）删除bond

[root@centos7 ~]# nmcli connection delete mybond0

Connection ‘mybond0’ (9ed2f027-bbb1-44d1-87fc-7f7275d7fe70) successfully deleted.

（3）删除从属接口

[root@centos7 ~]# nmcli connection delete bond-slave-ens34

Connection ‘bond-slave-ens34’ (a46ad620-d4b5-43f9-a73a-447785504a17) successfully deleted.

[root@centos7 ~]# nmcli connection delete bond-slave-ens38

Connection ‘bond-slave-ens38’ (66b1f44d-ad71-4576-8061-f6cba2b976e8) successfully deleted.

好了

以上就是关于网络接口配置Bonding的实例教程的详细内容，更多请关注学派吧其它相关文章！